Engine
Emissions
U.S. EPA Tier 4 Final/EU Stage IV
Peak Power Speed - 1,500 rpm - Gross - ISO 14396
Peak Power Speed - 1,500 rpm - Gross - SAE J1995
Peak Power Speed - 1,500 rpm - Net Power - SAE J1349
Peak Torque @ (speed) – SAE J1995
2104.00 lbf-ft
2852.00 N·m
Operating Specifications
Rated Payload – Standard (face material)
Rated Payload – Standard (loose material)
Rated Payload – High Lift (face material)
Rated Payload – High Lift (loose material)
Buckets
Transmission
Transmission Type
Cat switched reluctance electric drive
Axles
Hydraulic System – Steering
Steering System – Circuit
Steering System – Pump
Piston, variable displacement
Hydraulic System - Steering
Maximum Flow at 1,400-1,600 rpm
71.30 gal/min
270.00 l/min
Hydraulic System – Steering
Steering Cut Off Pressure
Steering Cycle Time (high idle)
Steering Cycle Time (low idle)
Service Refill Capacities
Cooling System (jacket water)
Cooling Systems (power train)
Diesel Exhaust Fluid Tank
Differentials and final drives – front
Differentials and final drives – rear
Hydraulic System – implement/steering
Sound Performance - Tier 4 Final/Stage IV
Operator Sound Level (ISO 6396)
Machine Sound Level (ISO 6395)
109.00 dB(A)
109.00 dB(A)
Hydraulic System Lift/Tilt
Lift/Tilt System – Circuit
EH-Positive Flow Control, Flow Sharing
Lift/Tilt System Pumps
Variable displacement piston
Hydraulic System - Lift/Tilt
Maximum Flow at 1,400-1,600 rpm
153.00 gal/min
580.00 l/min
Hydraulic System Lift/Tilt
Relief Valve Setting – Lift/Tilt
Hydraulic Cycle Time
Rackback
4.50 Seconds
4.50 Seconds
Raise
8.00 Seconds
8.00 Seconds
Dump
2.20 Seconds
2.20 Seconds
Lower Float Down
3.50 Seconds
3.50 Seconds
Total Hydraulic Cycle Time
18.20 Seconds
18.20 Seconds
Sound Performance - Tier 4 Final/Stage IV
Note (1)
The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
Note (2)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
Note (3)
The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
Brakes
Service Refill Capacities
Note
All non-road Tier 4 Final/Stage IV diesel engines are required to use: – The machine has the flexibility to run on either ultra-low-sulfur diesel fuel (ULSD with 15 ppm of sulfur or less) or up to B20 biodiesel when feedstock meeting ASTM D7467 specifications is blended with ULSD. – Cat DEO-ULS™ or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specifications are required. – Only use DEF that meets ISO 22241-1 standards.
Operating Specifications
Operating Weight – Standard
Operating Weight – High Lift
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
Operator Cab
ROPS/FOPS
ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards
Hydraulic System - Steering
Dimensions (Approximate) - Standard Lift
Ground to Top of Exhaust Stacks
Ground to Bumper Clearance
Rear Axle - Centerline to Bumper
Front Axle Centerline to Bucket Tip
Ground to Lower Hitch Clearance
Ground to Center of Axles
Clearance at Maximum Lift
B-Pin Height - Maximum Lift
Maximum Overall Height - Bucket Raised
Note
Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.
Dimensions (Approximate) - High Lift
Ground to Top of Exhaust Stacks
Ground to Bumper Clearance
Rear Axle - Centerline to Bumper
Front Axle Centerline to Bucket Tip
Dimensions (Approximate) – High Lift
Dimensions (Approximate) - High Lift
Ground to Lower Hitch Clearance
Ground to Center of Axles
Clearance at Maximum Lift
B-Pin Height - Maximum Lift
Maximum Overall Height - Bucket Raised
Note
Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.
Engine
Emissions
U.S. EPA Tier 4 Final/EU Stage V
Peak Torque @ (speed) - SAE J1995
2104.00 ft·lbf
2852.00 N·m
Operating Specifications
Rated Payload - High Lift (Moderate to High Digging Resistance)
Rated Payload - High Lift (Low to Moderate Digging Resistance)
Rated Payload - Standard Lift (Moderate to High Digging Resistance)
Rated Payload - Standard Lift (Low to Moderate Digging Resistance)
Transmission
Transmission Type
Cat switched reluctance electric drive
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit
EH-Positive Flow Control, Flow Sharing
Lift/Tilt System - Pump
Variable displacement piston
Relief Valve Setting - Lift/Tilt
Service Refill Capacities
Cooling System - Jacket Water
Cooling Systems - Power Train
Diesel Exhaust Fluid Tank
Differential - Final Drives - Front
Differential - Final Drives - Rear
Hydraulic System - Implement/Steering
Buckets
Axles
Brakes
Hydraulic System - Steering
Steering Cut Off Pressure
Steering Cycle Times - High Idle
Steering Cycle Times - Low Idle
Steering System - Circuit
Steering System - Pump
Piston, variable displacement
Hydraulic Cycle Times
Total Hydraulic Cycle Time
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
Dimensions (Approximate) - High Lift
Operating Specifications
Operating Weight - High Lift
Operating Weight - Standard
Operator's Cab
ROPS/FOPS
ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards
Service Refill Capacities
Note
All non-road Tier 4 Final/Stage IV diesel engines are required to use: – The machine has the flexibility to run on either ultra-low-sulfur diesel fuel (ULSD with 15 ppm of sulfur or less) or up to B20 biodiesel when feedstock meeting ASTM D7467 specifications is blended with ULSD. – Cat DEO-ULS™ or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specifications are required. – Only use DEF that meets ISO 22241-1 standards.
Operating Specifications
Rated Payload - Standard (Quarry Face)
Rated Payload - Loose Material (Standard)